Kinook Software Forums

Go Back   Kinook Software Forums > Visual Build Professional > [VBP] General Discussion

Thread Tools Rate Thread Display Modes
Old 04-29-2015, 02:56 PM
deramor deramor is online now
Registered User
Join Date: 05-11-2011
Posts: 25
Copy Files action sometimes results in corrupt file


I am using VBP 8.7. I have recently run into problems with build output files getting copied to a network share. The issue manifests itself in VBP as a failure to copy a file with the error "Access Denied". The build was trying to copy a file to a place where the previous build was. Each build overwrites the previous output.

In the past, I noticed there is some level of retry logic if a file can not be accessed that the Copy Files step employs. According to my help desk people, the issue was that the file about to be replaced was open by a user. Normally I would expect the copy command to enter its retry logic and eventually fail.

Instead what happened was the copy command proceeded and later failed. This left the file in a corrupt state and I couldn't delete or rename it. Its user rights were just gone.

My question is, how does VBP copy files? Is is the VB script:
' Copies a file
Sub vbld_CopyFile(SourceFile, DestFile, Overwrite)
' ensure that the target file is not read-only
If OverWrite Then vbld_MakeFileWriteable DestFile
' copy
vbld_FSO.GetFile(SourceFile).Copy DestFile, Overwrite
End Sub

What triggers the retry logic?

Do you have an suggestions as to server settings that can help eliminate this issue?
Reply With Quote
Old 04-29-2015, 03:29 PM
kinook kinook is online now
Join Date: 03-06-2001
Location: Colorado
Posts: 5,851
The Copy Files action calls the CopyFileEx Windows API to copy a file.

The action will retry a failed copy if 'Retries on failure' on the Errors tab is non-zero and the error result is one of:


or if 'Wait for share names to be defined...' on the Errors tab is checked and it is one of these errors:


If the action did not retry a failed copy, the CopyFileEx API must have returned another error code.

I don't know what could have caused that sort of problem.
Reply With Quote
Old 09-19-2016, 05:29 PM
jbenson jbenson is online now
Registered User
Join Date: 09-19-2016
Location: Minneapolis, MN USA
Posts: 7
Similar problem

I've been encountering a very similar problem with the Copy Files action in VBP.

I am also using Visual Build Pro 8.7. I've been working on getting a new build system up and running. The primary hold up right now is the build is not reliable. VBP "hangs" on a fairly regular basis while building certain steps, most often those involving a file copy step whose destination is a folder on a network share.

The behavior I see is VBP starts to copy a file and then stops dead. Often an empty (0 bytes) file is created on the destination. "Retries on failure" option seems to make no difference (checked or not). "Wait for share names to be defined" is checked. Even the "Terminate action if not complete after" option seems to be ignored.

If the copy step has "*.*" and "copy subdirectories (recursive) for the source options, the operation sometimes stops on the first file attempted. But, not every time the build runs.

When I check a "stuck" build in this situation, VBP is still running and has open file handles on the source and destination files (confirmed by the SysInternals "Handle" utility).

The build system I'm working with is Windows 8.1 running under VMware. The VBP is invoked as a Windows scheduled task running under an admin user account.

Any thoughts or suggestions on how to get past this problem? This build machine has been languishing in "limbo" for some time largely due to this issue.

Reply With Quote
Old 09-19-2016, 07:07 PM
kinook kinook is online now
Join Date: 03-06-2001
Location: Colorado
Posts: 5,851
In v9, you could check Use Robocopy to copy files on the Remote tab to use Robocopy instead of CopyFileEx to copy files and see if it makes a difference.

Otherwise, you could replace the Copy Files step with a Run Program action that calls xcopy or Robocopy.
Reply With Quote
Old 09-20-2016, 09:40 AM
jbenson jbenson is online now
Registered User
Join Date: 09-19-2016
Location: Minneapolis, MN USA
Posts: 7
Yes, I'm afraid I'm going to have to try something like that. Build is stuck again this morning in exactly the same place. Disappointing to say the least.
Reply With Quote

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

All times are GMT -5. The time now is 01:02 PM.

Copyright 1999-2022 Kinook Software, Inc.